Engineering Realities: Bottlenecks, Pycnometer Anomalies, and Hansen Solubility Parameters
If engineering has taught me anything so far, it’s that projects rarely move in a straight line . You map out a timeline, expect components to arrive on schedule, and assume lab measurements will yield textbook curves—only for practical realities to step in .
While our team was waiting for official HOD approval to issue a Raspberry Pi 4 board for our machine learning integration, the software development side hit a temporary bottleneck . Rather than sitting idle, we decided to pivot and begin building our empirical baseline dataset in the college chemistry lab with our professor's guidance .
However, getting consistent lab data proved to be much trickier than simply running samples through a balance .
The Laboratory Calibration & Mathematical Framework
Because ambient lab temperatures remained steady at a baseline of 25°C, thermal drift wasn't an immediate issue during testing . Our primary focus was measuring the absolute density of adulterated oil samples using a precision pycnometer and an electronic mass balance .
To compute the absolute density(sample), we used standard specific gravity relations relative to pure water at 25.0°C
Density(water) at 25°C = 0.99707g/cm^3
During calibration, our baseline vessel measurements were :
- Empty Pycnometer Bottle(m0): 8.479g
- Bottle + Water Mass(mw): 24.511g
- Net Water Mass:16.032g (our constant calculation denominator)
With the denominator fixed at16.032 g, we prepared 20 mL samples of mustard oil adulterated with varying percentages of palm oil to measure the net sample mass.
Experimental Setup & The Anomaly
To conduct each run, we filled the pycnometer completely with the prepared sample . As the capillary stopper knob was inserted, surplus oil spilled out from the top capillary channel, guaranteeing a fixed volume with zero trapped air bubbles before placing the bottle on the electronic balance.
We expected the sample density to follow a linear decline as the proportion of palm oil increased . Instead, our initial data points produced a surprising non-monotonic curve :
- 100% Mustard → 0.9081g/cm³
- 90% Mustard → 0.9090g/cm³
- 80% Mustard → 0.9079g/cm³
- 70% Mustard → 0.9066g/cm³
- 60% Mustard → 0.9056g/cm³
- 50% Mustard → 0.9074g/cm³
Analyzing the Non-Linear Trend
Rather than dropping steadily, the density initially spiked at 0.9090g/cm³ (90% mustard content), steadily decreased down to 0.9056g/cm³ at 60%, and then unexpectedly rose again to 0.9074 g/cm³
at the 50% mark
Raw lab measurements recorded at 25°C using standard pycnometer protocol
Troubleshooting & The Chemical Insight
Seeing our data bounce up and down was concerning . We systematically audited our physical procedure :
- Equipment Checks: The electronic balance calibration was verified and accurate
. - Volumetric Accuracy: Volumetric ratios were double-checked for preparation errors
. - Air Void Prevention: Pycnometer capillary seals were inspected to ensure no trapped microscopic air pockets remained
.
Despite eliminating mechanical errors, the non-linear pattern persisted . That was when our chemistry professor stepped in with a key chemical insight :
In commercial adulteration, two distinct oils are rarely just poured together directly . Over time or under thermal shifts, immiscibility and phase separation become noticeable . To overcome this, commercial blends use chemical solubilizers so the oils stay uniformly mixed without separating on store shelves
This introduced us to the concept of Hansen and Hildebrand Solubility Parameters . Without an appropriate solvent or co-solubilizer to match the solubility parameters of both lipid structures, raw physical mixing leaves localized density micro-variations throughout the solution, throwing off pycnometer readings .
Next Steps for Pure Drop
This setback proved to be a great learning experience . Building an engineering prototype isn't just about assembling hardware and capturing sensor numbers—it requires understanding the underlying physical and chemical domain .
Over the coming week, our focus shifts to :
- Researching specific organic solvent systems based on Hansen Solubility Parameters
. - Re-testing our mustard-palm oil compositions with uniform solvent blending to establish a true linear density benchmark
. - Proceeding with optical spectroscopy and refractive index profiling once our base CSV dataset stabilizes
.
I'll keep updating our progress here on The ECE Yatra as we refine our lab procedures and move closer to board-level hardware integration !



